TW Solar TWMNH-48HC440W 440Wp full black bifacial – pallet of 36 modules (15.84kWp)Pallet of 36 full-black bifacial dual-glass TNC modules, 440Wp each

Overview

A pallet of 36 TW Solar TWMNH-48HC440W full-black bifacial modules, 15.84kWp in total. The black frame and full-black laminate, with semi-tempered glass on both faces, give a uniform look in a 1,762×1,134×30mm format. At STC the module delivers 440Wp at 22.0% efficiency with 35.35V Voc and 15.89A Isc; at 135W/m² rear irradiance Tongwei rates it at 485.7W. Tongwei publishes a 2.0mm-glass version of 22.8kg and a 1.6mm-glass version of 21.9kg.

• TNC n-type half cells on G12R wafers
• Dual glass, 2.0mm semi-tempered on both faces
• 1,134mm width, 30mm black frame, 1500V DC rating
• Monofacial black-frame, full-black bifacial and bifacial black-frame versions
• 15-year product and 30-year linear power warranty

Versions in this range

All three types use Tongwei's TNC n-type monocrystalline cells, cut in half, on rectangular G12R wafers, laminated between two 2.0mm semi-tempered glass sheets with an anti-reflective front coating and held in a black anodised aluminium frame. The TWMNH-48HW is monofacial with an opaque rear, the TWMNH-48HC is a full-black bifacial module and the TWMNH-54HD is bifacial with transparent rear glass.

The 48-cell types carry 96 half cells in a 1,762×1,134×30mm module; the TWMNH-54HD has 108 half cells and measures 1,961×1,134×30mm. Tongwei packs all of them 36 per pallet, with 936 modules of the 48-cell types or 864 of the TWMNH-54HD per 40ft high-cube container. Bifaciality on Pmax is 80±10% for the 48HC and 80±5% for the 54HD.

Electrical design

Open-circuit voltage is about 35–37V for the 48-cell types and about 40V for the TWMNH-54HD, with short-circuit currents near 16A and a 30A maximum series fuse. The Tongwei manual sizes cables, fuses and other components on 1.25 times the marked Isc, requires a fuse on every parallel string and limits string Voc at the lowest site temperature to the 1500V DC rating and the inverter limit.

Different module models must not be mixed in one PV system, and Tongwei recommends keeping one current grade (I1, I2 or I3) per string. Mating connectors must be the same brand and type as the module connector. For landscape installation the manual asks for single cables of at least 1.2m on 48- and 54-cell G12R modules.

Mounting according to the manual

With four symmetrical clamps on the long side, the manual rates these modules at 5400Pa positive and 2400Pa negative test load, at clamp positions of 390–490mm for the 48-cell types and 440–540mm for the TWMNH-54HD. Short-side clamping gives ±1600Pa, or ±1200Pa with the clamps at the four corners. Clamps for the 48-cell types must be at least 60mm long and overlap the frame by at least 10mm.

Leave at least 10cm between frame and roof and 10mm between neighbouring modules, use a tilt of at least 10° so rain removes dust, and mount every module of a string at the same angle. Drilling the glass or frame voids the warranty; every frame and support must be earthed through the pre-drilled grounding holes.

Warranty and maintenance

Tongwei's limited warranty gives these types 15 years on materials and workmanship, three years more than its large TWMNH-66HD and TWMNF-66HD modules. The linear power warranty runs 30 years, with at most 1% loss in year one and 0.4% per year after, at least 87.4% at year 30; on dual-glass modules only front-side power is covered. The O&M manual limits washing pressure to 4MPa and forbids cleaning below 5°C.

Questions and answers