Haier Smart Cube HBP-5.0 battery module5.38kWh LFP battery module for Smart Cube energy controllers

Overview

The HBP-5.0 is the smaller battery module of the Haier Smart Cube, with 5.38kWh total and 5.2kWh usable energy from lithium iron phosphate cells. It charges and discharges at up to 2.5kW, with 3.75kW for 10 seconds. One to six modules stack under an HH1P or HH3P energy controller and can be combined with HBP-8.0 modules. The IP66 module measures 767×270×260mm, weighs 55kg and can be floor-standing or wall-mounted.

• Energy controllers HH1P 3–6kW and HH3P 5–25kW
• HBP-5.0 and HBP-8.0 modules, 1–6 per controller
• Up to 48.36kWh per stack, 20 systems in parallel
• 0ms backup with the Energy Gateway
• Optional bi-directional DC EV charging module up to 25kW
• IP66 controller and batteries

How it works

Smart Cube is built as a stack: an energy controller (hybrid inverter) sits on top of one to six HBP battery modules, and an optional DC EV charging module can be added to the same column. HBP-5.0 modules hold 5.38kWh and HBP-8.0 modules 8.06kWh, so one stack ranges from about 5kWh to 48.36kWh. Modules of both sizes can be combined under one controller. The battery side works at 300–600V with single-phase controllers and 600–900V with three-phase controllers.

The single-phase HH1P controllers (3–6kW) have two MPP trackers and a 600V input; the three-phase HH3P controllers (5–25kW) accept 1100V on two to four trackers. All trackers take 16A, and the PV array can reach twice the rated output, for example 32kW on the HH3P-20K.

Backup, EV charging and expansion

With the Energy Gateway (HG-SS single-phase, HG-TS three-phase) the controller supplies the home with a 0ms load-side transfer when the grid fails, provided the controller power exceeds the backup load. The gateway also offers breaker positions for further loads, a generator input with 2-wire start, and whole-home or partial backup. Haier states that up to 20 systems can run in parallel, for a total of 960kWh.

The DC EV charging module (HEVDC-12S2C5 at 12.5kW or HEVDC-25S2C5 at 25kW, CCS2 connector, 150–1000V) stacks with the controller and charges a car directly from PV and battery. It is prepared for bi-directional V2X operation, which Haier says depends on the vehicle and on standards still to be published. Charging is tracked and scheduled in the app.

Installation

Controller and batteries are rated IP66 and can be floor-standing or wall-mounted. The single-phase controller weighs 18kg and is naturally cooled; the three-phase controller weighs 36kg and uses smart air cooling. HBP-5.0 modules weigh 55kg and HBP-8.0 modules 70kg, all 767×270×260mm. A three-phase stack of six HBP-8.0 modules is 1990mm high and 850mm wide with decorative covers. Haier quotes about 15 minutes for stacking and 5 minutes for commissioning.

Monitoring and settings

Controllers communicate over WLAN, Fast Ethernet and RS485; the plug-in HC-U4G CommMod adds a 4G, 3G or 2G connection. The Power Sensor meter (single- or three-phase, RS485 Modbus) provides grid measurement for export limits. The Haier Smart Cube app shows production, storage and consumption, schedules EV charging and can monitor a heat pump.

Questions and answers